Pulse Picker MP1

Pulse picker MP1 consists of built-in fast driver and a Pockels cell. This unit is able to select pulses at up to 600 kHz rate.

 

MP1 requires sync pulses from the laser for driver control or can be used with pMaster 4.0 generator. In setup with pMaster 4.0H generator can be synchronized for single pulse picking from max 30 MHz repetition rate pulse train.

 

MP1 pulse picker has BBO Pockels cell and is set for quarter wave voltage operation. On special requests BBO cell can be changed to KTP Pockels cell for half wave voltage operation.

 

Operation instructions:

1. pMaster 4.0 and MP1 pulse picker setup for pulse picking at up to 600 kHz rate

EKSMA Optics MP1 Pulse Picker Scheme

Delivery

Estimated delivery time: Request

Description

Pulse Synchronization and Delay Generator

Code Description Price Delivery Add to cart
pMaster 4.0H 4 output channels for trigger pulses with built-in High Voltage supply Request Request To cart

Pulse Picker for up to 600 kHz Operating Rate

Code Description Price Delivery Add to cart
MP1-BBO-3.5 With BBO clear aperture 3.5 mm, λ/4 operation at 1030 nm Request Request To cart
Delicious

 

Specifications of Digital synchronization and delay pulse generator pMaster 4.0H

 

pMaster features 4 independent programmable channel outputs and communication via USB port with LabView compatible drivers for full control over all parameters.

 

Programmable Timing Generator
Channel modes
Single shot, burst, normal, duty cycle
Control modes
Internally triggered, externally triggered and external gate
Delay range
0 to 1000 s
Delay accuracy
1.5 ns + 0.0001 delay
Delay resolution
250 ps
Delay jitter
<400 ps RMS
Pulse inhibit delay / output inhibit delay
120 ns / 50 ns
Trigger input module
Trigger input rate
DC - 5 MHz
Trigger insertion delay
<180 ns
Trigger jitter
<800 ps RMS
Minimal pulse width
2 ns
Trigger threshold
0.2 - 15 V DC
Maximum input voltage
60 V peak
Input impendance
1.5 k Ω + 40 pF
Resolution
10 mV
External clock input module
External clock input rate
10 MHz – 100 MHz
Minimal pulse width
100 ps
Pulse amplitude
1 V rms (min) – 5 V rms (max)
Input impedance
102 Ω
High voltage power supply for PC driver
Built-in
Dimensions W x D x H, mm
482 x 387 x 88 mm

Specifications of MP1 Pulse Picker

 

MP1-BBO unit has BBO crystal Pockels cell however on special request it can be changed to KTP Pockels cell.

 

Pulse picker
MP1 - BBO
Max laser repetition rate for single pulse picking
30 MHz
Built-in driver
operates at up to 600 kHz rep. rate
HV power supply
Required1
Operation
Quarter wave, λ/4
HV pulse duration
15-5000 ns
HV pulse rise and fall time
<7 ns
Pockels cell contrast ratio, VCR2
>1:500
Pockels cell transmission3
>98% at 1030 nm
Clear aperture
Dia 3.5 mm
Cooling
Water
Dimensions L x W x H, mm
230 x 90 x 69 mm

 

Notes:

1 - requires one HV power supply with max 4 kV output and maximal output power 120 W. Optimal HV power supply is provided in generator pMaster 4.0H.

2 - VCR - contrast ratio when voltage is applied to the cell.

3 - other particular laser wavelengths or wavelength ranges are available on request.

Eksma Optics is a member of: Linked.in Twitter.com
PayPal.com Paysera
© Optolita UAB 2013. All rights reserved.
Touched by digitouch!