EKSMA Optics uses cookies to give you the best shopping experience. If you continue to use our services, we will assume that you agree to the use of such cookies.

Understand
Your cart
0
There are no items in your cart.
Add items to your cart and request an official quote or order online
Your cart
0
Products categories
Login/Register
There are no items in your cart.
Add items to your cart and request an official quote or order online

EKSMA Optics uses cookies to give you the best shopping experience. If you continue to use our services, we will assume that you agree to the use of such cookies.

Understand
arrow--left
Go back

Timing Generators for Laser Sync

Timing Generators for Laser Sync

The TG10 is a timing generator dedicated to the synchronization of laser systems and laser components: Pockels cell drivers, acousto-optical modulator drivers, laser diode and flash lamp drivers, detectors, data acquisition systems, laser pulse pickers.

Request
delivery Estimated delivery time: Request
Products
Specifications
Brochures
Description
Code Description Price Delivery Add to cart
TG10 Laboratory type 5472 $ 4 - 5 days
SY4000-OEM OEM version Request Request
MODEL Timing Generator TG10
Time Base
Internal source 100 MHz 0.2 ppm TCXO
External source, Optical clock 20-100 MHz
Internal rate generator
Source 100 MHz clock, Optical clock, SYNC IN, Software command
Rate (T0 period) 50 ns - 100 s (0.01 Hz to 20 MHz)
Resolution 10 ns or 1 Optical period or 1 SYNC IN period
RMS jitter <350 ps
External trigger, SYNC IN input
System modes Direct SYNC IN, SYNC IN re-clocked to Optical clock
Rate DC to 20 MHz
Threshold 1.3 V
Input range 0-5 V
Trigger slope rising edge
RMS jitter, Direct SYNC IN <120 ps
RMS jitter, SYNC IN re-clocked <5 ns
Insertion delay <80 ns
Delay generators
Channels, total 8
High res channels 5
High res channels, resolution 25 ps
Low res channels 3
Low res channels, resolution <10 ns
Delay 0-150 ms
Pulse width 2 ns - 150 ms
Accuracy, high res channel 2.5 ns + 0.000001 setpoint
Accuracy, Low res channel ≤10 ns + 0.000001 setpoint
Time base, Internal clock 100 MHz, 0.2 PPM TCXO
RSM jitter, channel to channel <30 ps TTL output, <4 ps PRET output
Configuration switch
System modes Single shot burst, continuous, frequency divider, GATE IN, inverted GATER IN
Burst counter 1 - 65535
Frequency divider 1 - 32767
Outputs, TTL/COMS
Voltage @50 Ω Load 2.5 V or 4.5 V
Voltage @1 MΩ load 5 V or 9 V
Voltage selection 5 V/9 V Internal jumper
Impedance 50 Ω
Rise time 1.5 ns typ
Outputs, PRET
Pulse amplitude @ 50 Ω load >1V
Impedance 50 Ω
Rise time 200 ps typ
Outputs, differenctial
Type LVPECL
Output, analog
DAC resolution 12 bit
Max amplitude @50 Ω 1 V
Power
Voltage 12 V±10%
Power 15 W max
EKSMA Optics Timing generator - TG10 for Laser Sync
193.88 kB
download PDF
EKSMA Optics Timing generator - TG10 for Laser Sync Main Components
63.25 kB
download PDF
EKSMA Optics Timing generator - TG10 for Laser Sync Manual
963.99 kB
download PDF

The compact timing generator TG10 with an ultra-stable 0.2 ppm internal clock creates up to 8 delay channels precisely synchronized to the internal or external clock at up to 100 MHz repetition rate. TG10 features a precise trigger output with an exceptionally low 3-5 ps jitter, which makes it an ideal choice for high-speed acquisition systems like streak camera triggering.

In addition to the standard pulse generator features, TG10 allows to combine up to 4 pulse outputs to signals by OR, AND, NOT logical operations, and instantly switch between two configurations in delay blocks. Burst counter, gate input, frequency divider, or software commands may serve as the configuration switching signal sources. Configuration switch is used to control optical pulse pickers (EOM or AOM) in a highly flexible manner.

The following are the key features of the TG10 module in addition to standard pulse generator:

  • Ability to lock to an external clock source, usually photo-diode pulse train. The triggering system is locked to the laser oscillator then, and trigger time is always in phase with the optical pulse.
  • Instant switch between two configurations in delay blocks. Burst counter, gate input, frequency divider, or software commands may serve as the configuration switching signal sources. Configuration switch is used to control optical pulse pickers (EOM or AOM) in a highly flexible manner.
  • Low jitter sync pulse output is used for high-speed acquisition systems like streak camera triggering. The typical jitter is 3...5 ps to the optical pulse.
  • Control connector. The software-controllable multiplexer may divert any of the output signals to this connector to sniff what is on other connectors without disturbing them.
  • Clock output: 1:1, 1:2 frequency.
  • Up to 4 pulse outputs can be combined to single signals by OR, AND, NOT logical operations.
  • DAC output, controlling, e.g. AOM pass though.

TG10 has the following input and output channels:

  • OUTx - five digital general-purpose output (4.5V @ 50 Ω)
  • AN OUT - analog output with 12-bit resolution (1V @ 50 Ω)
  • COM TRIG - common trigger output. Configurable source (2.5V @ 50 Ω)
  • PRE TRIG - precise trigger output channel. Configurable source (>1.5V @ 50 Ω)
  • GATE IN - configuration switch and burst control input. (LVTTL, tolerates 5V. 0.2 mA pull-down)
  • SYNC IN - trigger input for DC to 20 MHz frequencies. (LVTTL, tolerates 5V. 0.2 mA pull-down)
  • CLK IN - clock input for 10 MHz to 100 MHz frequencies. (0.5V to 3.3V @ 50 Ω pk-pk, sine or pulses)

The TG10 device has an LCD touch screen for the manual control and a tunable knob for the adjustment of selected values set on the touch screen. Instructions of required actions are always displayed at the bottom of the screen. The timing generator has a digital control interface via CAN bus. Communication protocol with description for CAN is provided on request. CAN to USB converter is also available from EKSMA Optics.

Applications:

  • Passive or active mode locked, Q-switched lasers, pulsed or QCW
  • Data acquisition system triggering
  • General purpose pulse generator
  • Precise system clock source
  • Laser pulse train converting to the clean clock source
  • All functions listed above simultaneously at once!

Features:

  • Ultra-stable internal clock 0.2 ppm
  • Precise delay control in range 2 ns to 150 ms
  • 25 ps timing resolution
  • Hi-accuracy synchronization to the external pulse train
  • DAC output
  • Frequency divider
  • Frequency divider for photodetectors
  • Measurement of: 

                                        -Optical clock frequency

                                        -Triggering frequency 

                                        -Delay